Cadillac Escalade

Issue: On certain vehicles, the daytime running lamps (DRLs) may stay on when the headlamps are on. Canadian regulations require the DRLs to turn off when the headlamps are on. Safety Risk: Daytime running lamps that stay on could cause glare for oncoming drivers and increase the risk of a crash. Corrective Action: General Motors will notify owners by mail and and send a wireless over-the-air software update to eligible vehicles to update the body control module (BCM) software. Alternatively, you may schedule an appointment to have the update performed at a GM dealer.

Issue: On certain vehicles, parts inside the rear axle shafts may not have been manufactured properly. Over time, this could lead to wear that can cause noise and vibration. If you continue to drive the vehicle with these symptoms, an axle shaft could seize and cause a loss of power to the wheels. Safety Risk: A loss of power to the wheels could increase the risk of a crash. Corrective Actions: General Motors will notify owners by mail and instruct you to take your vehicle to a dealer to replace the left and/or right-rear axle shafts.

Issue: On certain vehicles, the outboard seat belts for the third-row seat may have been installed incorrectly. As a result, the seat belts could be mis-routed or damaged by sharp edges on the seat-folding parts. Safety Risk: A damaged seat belt could break in a crash and increase the risk of injury. Corrective Actions: General Motors will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the third-row outboard seat belts for correct routing and damage. The seat belt path will be corrected if required. Damaged seat belts will be replaced.

Issue: On certain vehicles, there could be a reduction in power brake assist due to a decrease in output from the vacuum pump. This could cause a hard brake pedal and create an increase in brake pedal effort that is required to stop the vehicle. Note: This is an expansion of Transport Canada Recall 2019-324. Safety Risk: A sudden increase in brake pedal force could lead to an increase in stopping distance. This could increase the risk of a crash. Corrective Actions: The company will notify owners by mail and instruct you to take your vehicle to a dealer to reprogram the electronic brake control module.

Issue: This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones. Note: This is a voluntary recall that is not being conducted under the requirements of the Motor Vehicle Safety Act. Safety Risk: Glass that breaks in to large pieces could create a risk of injury. Corrective Actions: The company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “DOT 287” along with the lettering “VMR” (Replacement Market) and a date code that is before July 2019. This information is printed on the bottom corner of the glass. Consumers should contact Vitro's customer service at 1-412-995-6457 or argbacklites@vitro.com to arrange for replacement of the glass.

Certain vehicles may experience a temporary loss of electric power steering (EPS) assist followed by a sudden return of EPS assist, particularly during low-speed turning manoeuvres due to an electrical/software issue. If EPS assist is lost and suddenly returned, the unexpected change in steering effort could affect vehicle control, which would increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will update the EPS module software. Note: If power steering assist is lost and the vehicle reverts to manual steering, a dash message would be displayed stating there is an EPS problem. Additionally, this issue could also affect radio, stabilitrak, the driver information centre, chime, door-lock, air conditioning, and/or cruise control function.

On certain vehicles equipped with Continental P275/55R20 CrossContact LX20 tires, a manufacturing defect could cause a lack of adhesion between belts in the tire. Affected tires may exhibit localized tread wear, excessive vibration, noise and bulging in the tread area. Continued use could cause the belts to separate, which could lead to full belt/tread loss. This could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect tire date code markings to determine whether they are from the affected date code. Affected tires will be replaced.

General Motors Canada is conducting a voluntary Safety Improvement Program involving passenger airbag inflators in vehicles that were originally sold or ever registered in certain areas of the United States that experience high or moderate levels of heat and humidity, and that were subsequently imported into Canada. Dealers will replace the passenger inflator on affected vehicles. Owners who believe their vehicles may have been originally purchased or registered in the states listed below should contact a General Motors dealer. This action is not being conducted under the requirements of the Motor Vehicle Safety Act. Affected states: American Samoa and the U.S. Virgin Islands, Alabama, Arizona, Arkansas, California, Delaware, District of Columbia, Florida, Georgia, Guam, Hawaii, Illinois, Indiana, Kansas, Kentucky, Louisiana, Maryland, Mississippi, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Puerto Rico, South Carolina, Tennessee, Texas, the Northern Mariana Islands (Saipan), Virginia and West Virginia.

On certain vehicles, a defect in the ignition lock cylinder could cause the key to stick in the "start" position if the vehicle interior temperature is sufficiently high. If the vehicle is operated in this condition and the interior temperature cools or the vehicle goes off-road or is subjected to some other jarring event, the key could move out of the "start" position, rotate past the "run" position and into the "accessory" position. If this were to occur, engine power, power steering and power braking would be affected, increasing the risk of a crash causing injury and/or damage to property. The timing of the key movement out of the “run” position, relative to the activation of the sensing algorithm of the crash event, may also result in the airbags not deploying in a subsequent collision, increasing the risk of injury. Correction: Dealers will inspect the steering column for identifying information and replace if necessary.

Certain vehicles may not comply with the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 208 - Occupant Protection. The top cover of the passenger side instrument panel may have been manufactured incorrectly, which could result in the passenger side airbag deploying irregularly. This would increase the potential for a front passenger seat occupant injury (where deployment is warranted). Correction: Dealers will replace the instrument panel top cover.

Certain vehicles may not comply with the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 208 - Occupant Protection. The passenger side airbag mounting may not have been welded to specification, which could affect airbag deployment and result in non-compliance to the standard, increasing the risk of injury in a crash. Correction: Dealers will replace the instrument panel right side upper trim panel.

On certain vehicles, the intermediate steering shaft attaching bolts may not have received adequate tightening torque during vehicle assembly. This could allow the joint to separate, resulting in a loss of steering capability. A loss of steering control could result in a crash causing property damage and/or personal injury. Correction: Dealers will tighten the intermediate steering shaft bolts to specifications.

On certain vehicles equipped with a Heated Washer Fluid System (HWFS), a short circuit on the printed circuit board for the washer fluid heater may overheat the control-circuit ground wire. A repair was implemented in a recall in 2008, however, there have been new reports of thermal incidents on heated washer fluid system modules after this improvement was installed. This situation may cause some minor distortion, but also could lead to melting of the plastic around the heated washer fluid system, or cause a fire. Correction: Dealers will permanently disable and remove the heated washer fluid module. An updated page will be provided and inserted in the Owner Manual to document the removal of the feature.

On certain vehicles equipped with a heated washer fluid system, a short circuit on the printed circuit board for the washer fluid heater may overheat the control-circuit ground wire. This situation may cause other electrical features to malfunction which could cause smoke and in some cases a fire. Correction: Dealer will install a wire harness with an in-line fuse.

On certain vehicles, the 2nd row centre occupant seat belt routing may make it difficult to position the lap portion of the safety belt low around the hips of occupants. A lap portion of the seat belt routing that is not low and snug on the hips can allow unfavourable occupant kinetics in the event of a crash. Moreover, the higher routing allows the lap belt to ride up on an occupant's abdomen instead of fitting low around their hipbones, and therefore, can expose them to more risk of abdominal and internal organ injury. Correction: Dealers will modify the guide loop.

On certain vehicles, the relief valve o-ring seal within the brake hydro-boost module could fail. If this happens during braking applications, the driver may be able to hear an engine compartment noise similar to the sound that occurs when the steering wheel is turned to a full stop position. The driver could also experience a slight increase in steering efforts while braking and parking. Under certain driving conditions, a slight increase in the applied brake pedal effort may be required to achieve the same vehicle deceleration rate as prior to the seal failure. Correction: Dealers will inspect the hydro-boost module, and replace it, if necessary.

On certain vehicles, the following statements were omitted from the SIR caution label: "Never put a rear-facing child seat in the front" for the vehicles without an air bag switch or "Never put a rear-facing child seat in the front unless air bag is off" for vehicles with an air bag switch and "Sit far back as possible from the air bag". The statements are printed in the Owner's Manual. Correction: None required as instructions are in the owners manual and this is well known by the public.

Certain vehicles fail to conform to CMVSS 209, seat belt assemblies. These vehicles have a condition where one or two sensors in the driver's and front seat passengers seat belt retractors may be inoperative. The seat belt retractors will lock when the belt webbing is extracted during a crash; however the mechanism that locks the seat belt retractor when the vehicle decelerates quickly, such as during heavy braking, may not restrain the occupant as intended during a crash, and could result in injury to the occupant. Correction update: None required as no effect on vehicle safety. See recall 04-158.