Chevrolet Express in Canada - Canadian Prices, Trims, Specs, Photos, Recalls | AutoTrader.ca

Chevrolet Express

Chevrolet Express

Model Overview

No model overview available

Photos

Reviews and News

Owner Scores

This vehicle has not yet been reviewed

Recall Information

Recall number
Recall date
System affected
Model year(s) affected
Recall number
2021-166
Recall date
2021-03-18
System affected
Electrical
Model year(s) affected
2021
Manufacturer Recall Number:
N202325160
Units Affected:
877
Notification Type:
Safety Mfr
Issue: On certain vehicles, the positive battery cable terminals could come into contact with the fuse block assembly. If this happens, there could be a short circuit. Safety Risk: A short circuit could create a fire risk. Corrective Actions: General Motors will notify owners by mail and instruct you to take your vehicle to a dealer to remove part of the anti-rotation tab on both positive battery cable terminals.
Recall number
2020-479
Recall date
2020-10-07
System affected
Other
Model year(s) affected
2011 2012 2013 2014 2015 2016 2017 2018
Manufacturer Recall Number:
18067
Units Affected:
56,979
Notification Type:
Inconsequential
Issue: Certain vehicles may have incorrect body control module software. As a result, the immobilization system is not active during the learning procedure for a new "unlearned" blank replacement key could be used during a 30 minute reprogramming procedure to disable the immobilization system. During this time, the vehicle cannot be driven. Safety Risk: This small error does not affect vehicle safety. Corrective Actions: This is not a recall. General Motors has made changes to vehicle software to ensure that all unsold and new vehicles have the correct body control module software.
Recall number
2019-450
Recall date
2019-09-06
System affected
Lights And Instruments
Model year(s) affected
2019
Manufacturer Recall Number:
N192264501
Units Affected:
7,308
Notification Type:
Compliance Mfr
Issue: On certain vans, the seat belt and airbag warning lights will not turn on for approximately 5 seconds after the ignition is switched to the ON or start position. Canadian regulations require these lights to turn on to demonstrate that the airbag system is working properly (bulb check) and to remind a driver to fasten their seat belt. Safety Risk: Warning lights that do not turn on during the start-up check could confuse a driver. In addition, the driver would not see a reminder to fasten their seat belt. This could create an increased risk of injury in a crash. Corrective Actions: The company will notify owners by mail and instruct them to take their vehicle to a dealer to reprogram the instrument panel cluster.
Recall number
2019-243
Recall date
2019-05-23
System affected
Structure
Model year(s) affected
2019
Manufacturer Recall Number:
N192218960
Units Affected:
8
Notification Type:
Compliance Mfr
Issue: Certain vehicles were built with the wrong type of glass in one or both of the rear-quarter windows. Tempered glass was used in place of laminated glass. As a result, the vehicles may not meet the ejection mitigation requirements of the Canadian regulations. Safety Risk: Vehicles built with incorrect side window glass could create an additional risk of injury in a rollover or side impact crash. Corrective Actions: The company will notify owners by mail and instruct them to take their vehicle to a dealer to replace the tempered window glass with laminated glass. For long wheelbase vehicles, the left rear-quarter window will be replaced. For short wheelbase vehicles, both the left and right rear-quarter windows will be replaced.
Recall number
2018-525
Recall date
2018-09-21
System affected
Heater And Defroster
Model year(s) affected
2016 2017 2018
Manufacturer Recall Number:
18299
Units Affected:
1,077
Notification Type:
Safety Mfr
On certain vehicles equipped with a single manual rear climate control module (CCM), the CCM could overheat when the temperature is set to maximum heat or the knob is set to maximum floor vent. If this occurs, the insulation material used on the CCM terminal connectors could catch fire, increasing the risk of injury and/or damage to property. Correction: Dealers will remove the insulation from the CCM terminal connectors.
Recall number
2018-234
Recall date
2018-05-04
System affected
Electrical
Model year(s) affected
2014 2015 2016
Manufacturer Recall Number:
18155
Units Affected:
22,078
Notification Type:
Safety Mfr
On certain vehicles equipped with power windows, liquid can enter the power window switches causing corrosion and lead to a high electrical resistance. This could cause the switch to heat up, smoke or melt, which would increase the risk of fire causing injury and/or damage to property. Correction: Dealers will replace the driver’s side window switch with a switch that has additional protection against liquid intrusion.
Recall number
2018-212
Recall date
2018-04-27
System affected
Accessories
Model year(s) affected
2011 2012 2013 2014 2015 2016 2017
Manufacturer Recall Number:
18146
Units Affected:
368
Notification Type:
Safety Mfr
On certain vehicles equipped with Kidde fire extinguishers with black plastic handles and valves, the fire extinguishers may become clogged or require excessive force to activate. Also, the nozzle may detach from the valve assembly with enough force that it could cause injury, and fail to discharge. In case of fire, failure of the extinguisher to function could result in injury and/or property damage. Correction: Owners will be provided with instructions on how to inspect the fire extinguisher to see if it is recalled. Replacement fire extinguishers will be supplied by Kidde directly. Note: For more information about recalled fire extinguishers, please visit www.kidde.com
Recall number
2015-352
Recall date
2015-08-05
System affected
Brakes
Model year(s) affected
2011 2012 2013 2014
Manufacturer Recall Number:
15588
Units Affected:
442
Notification Type:
Safety TC
Certain vehicles equipped with a hinged left side rear door may have a condition where inadequate clearance between the rear brake lines and the lower fuel filler hose clamp may result in abrasion to one or both rear brake lines. This condition could cause brake fluid loss which could result in decreased brake line pressure, increased brake pedal travel and increased stopping distance, increasing the risk of a crash causing injury and/or damage to property. This condition could cause various warning lights to illuminate in the instrument panel of the vehicle such the red “BRAKE” telltale symbol; illumination of the Stabilitrak telltale symbol; scrolling display of “Service Brake”, “Service Stabilitrak,” and “Service Traction Control” messages in the Driver Information Centre (DIC); and audible alerts/chimes. Correction: Dealers will inspect the brake lines. If the clearance is found to be below specification, the brake lines will be replaced with a new part design that provides adequate clearance.
Recall number
2014-432
Recall date
2014-10-03
System affected
Electrical
Model year(s) affected
2014
Manufacturer Recall Number:
14515
Units Affected:
5,071
Notification Type:
Safety Mfr
On certain vehicles, the chassis electronic module may have been contaminated at time of manufacture, which could cause an electrical short to occur within the module. This could cause the vehicle's check engine light to be displayed, or cause the engine to fail to start or stall, resulting in a loss of motive power. If the vehicle is equipped to support electric trailer brakes, the vehicle could also lose trailer brake function and display a "Service Trailer Brake System" indicator. These issues could increase the risk of a crash resulting in injury and/or damage to property. Correction: Dealers will replace the module with a revised part.
Recall number
2014-352
Recall date
2014-08-19
System affected
Fuel Supply
Model year(s) affected
2011 2012 2013 2014
Manufacturer Recall Number:
14321
Units Affected:
13
Notification Type:
Safety Mfr
On certain compressed natural gas (CNG) fuelled vehicles, the CNG high pressure regulator may leak natural gas. Should a leak occur in the presence of an ignition source, a fire or explosion could result, increasing the risk of injury and/or damage to property. Correction: Dealers will replace the regulator. Note: If a leak is suspected, owners should not start nor drive their vehicles, and have the vehicle immediately towed, inspected and repaired.
Recall number
2014-083
Recall date
2014-03-18
System affected
Seats And Restraints
Model year(s) affected
2009 2010 2011 2012 2013 2014
Manufacturer Recall Number:
14082
Units Affected:
25,710
Notification Type:
Compliance Mfr
Certain vehicles may not comply with the requirements of Canada Motor Vehicle Safety Standard 201 - Occupant Protection. During a frontal impact below the airbag deployment threshold, if an unbelted front passenger's head were to impact the instrument panel where the passenger airbag is located, it could decelerate at a rate higher than what is allowable by the standard. This could increase the risk of injury. Correction: Dealers will install energy absorbing trim pieces on the passenger side of the instrument panel, and on 2012-2014 model year 1500 series vehicles, dealers will also replace the front passenger seat belt retractor.
Recall number
2013-206
Recall date
2013-06-12
System affected
Fuel Supply
Model year(s) affected
2012
Manufacturer Recall Number:
13139
Units Affected:
9
Notification Type:
Safety Mfr
On certain vehicles, underbody shut-off solenoid connectors for the compressed natural gas (CNG) fuel tanks may corrode and form a high-resistance short. This could result in a vehicle fire causing property damage and/or personal injury. Correction: Dealers will replace the solenoid at the fuel tanks and the regulator, and the 30 amp fuel pump fuse will be replaced with either a 7.5 amp fuse (for the four tank configuration) or a 5.0 amp fuse (for the three tank arrangement). In addition, the wiring routing will be adjusted, if necessary, to eliminate any undue tension on the connector, and anti-corrosion sealing plugs will be installed into the valve body.
Recall number
2013-008
Recall date
2013-01-14
System affected
Other
Model year(s) affected
2013
Manufacturer Recall Number:
12332
Units Affected:
73
Notification Type:
Compliance Mfr
Certain vehicles fail to conform to Canada Motor Vehicle Safety Standard 114 – Theft Protection and Rollaway Prevention. Specifically, the ignition key can be removed from the ignition when it is not in the OFF position. This could result in unintended vehicle movement, which could cause a crash resulting in property damage and/or personal injury. Correction: Dealers will replace the ignition lock cylinder.
Recall number
2013-001
Recall date
2012-12-31
System affected
Other
Model year(s) affected
2013
Manufacturer Recall Number:
12331
Units Affected:
6,310
Notification Type:
Compliance Mfr
Certain vehicles fail to conform to Canada Motor Vehicle Safety Standard (CMVSS) 102 – Transmission Control Functions, and CMVSS 114 – Theft Protection and Rollaway Prevention. A fractured park lock cable, or a defective steering lock module, may have been installed during vehicle assembly. This could allow the driver to shift out of PARK with the key in the OFF position or removed from the ignition. As well, the transmission may be shifted out of PARK without first depressing the brake pedal. The key may also be rotated to the OFF position and removed while the shifter is not in PARK. These issues could result in unintended vehicle movement, which could cause a crash resulting in property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the steering column assembly.
Recall number
2012-265
Recall date
2012-08-08
System affected
Fuel Supply
Model year(s) affected
2003 2004
Manufacturer Recall Number:
12166
Units Affected:
951
Notification Type:
Safety Mfr
On certain vehicles equipped with a left side cargo door, and originally sold in or currently operated in areas of heavy road salt usage during winter months (Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island, and Newfoundland & Labrador), the fuel filler pipe could corrode and become perforated. This could allow fuel to leak onto the ground while refuelling the vehicle. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will replace the fuel filler pipe.
Recall number
2012-105
Recall date
2012-03-22
System affected
Steering
Model year(s) affected
2012
Manufacturer Recall Number:
12055
Units Affected:
712
Notification Type:
Safety Mfr
On certain vehicles, the steering gear pitman arm may not have been manufactured correctly and could fail. Pitman arm failure would cause a loss of steering control, which could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the steering gear pitman arm.
Recall number
2011-394
Recall date
2011-11-07
System affected
Airbag
Model year(s) affected
2012
Manufacturer Recall Number:
11302
Units Affected:
37
Notification Type:
Safety Mfr
On certain vehicles, the second stage of the front passenger dual-stage airbag may not deploy as commanded during a severe frontal impact. Failure of the airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Correction: Dealers will replace the front passenger airbag.
Recall number
2011-188
Recall date
2011-05-06
System affected
Brakes
Model year(s) affected
2011
Manufacturer Recall Number:
11126
Units Affected:
631
Notification Type:
Safety Mfr
On certain vehicles, the right rear brake hose may contact the tire or wheel rim, which could cause chafe damage resulting in a brake fluid leak. This could increase stopping distances, possibly resulting in a crash causing property damage and/or personal injury. Correction: Dealers will secure the right rear brake hose to ensure sufficient clearance to the wheel/tire assembly. The brake hose will also be inspect for damage and, if necessary, replaced.
Recall number
2010-454
Recall date
2010-12-17
System affected
Suspension
Model year(s) affected
2011
Manufacturer Recall Number:
10426
Units Affected:
3,945
Notification Type:
Safety Mfr
On certain vehicles, the rear axle cross pin was improperly heat treated (during the manufacturing process) and could fracture and become displaced within the rear differential. As a result the driver may hear a banging noise emanating from the rear axle. Also, if the pin shifts out of position it could create an interference and cause the rear axle to lock. This could cause a loss of vehicle control, which could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the rear axle cross pin.
Recall number
2010-231
Recall date
2010-07-15
System affected
Electrical
Model year(s) affected
2010
Manufacturer Recall Number:
10216
Units Affected:
218
Notification Type:
Safety Mfr
On certain Express and Savana 2500, 3500 and 4500 vehicles equipped with a 145 Amp alternator, a low resistance short could develop within the voltage regulator. In some cases, if the circuit does not open, the low resistance short could eventually generate enough heat to result in an engine compartment fire causing property damage or personal injury. Correction: Dealers will inspect and, if necessary, replace alternator. Note: This recall supersedes recall 2010106.
Recall number
2010-106
Recall date
2010-04-06
System affected
Electrical
Model year(s) affected
2010
Manufacturer Recall Number:
10091
Units Affected:
172
Notification Type:
Safety Mfr
Certain vehicles equipped with a 145 amp alternator may develop a low resistance short within the voltage regulator. In some cases, if the circuit does not open, the low resistance short could eventually generate enough heat to result in an engine compartment fire causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the alternator. Note: This recall is superseded by recall 2010231.
Recall number
2010-072
Recall date
2010-03-11
System affected
Heater And Defroster
Model year(s) affected
2009 2010
Manufacturer Recall Number:
10012
Units Affected:
1,414
Notification Type:
Compliance Mfr
Certain vehicles were built with heating, ventilation, and air conditioning (HVAC) control knobs that may fracture and spin on the control shaft. If this happens, the driver may no longer be able to control the heating, cooling, and ventilation for the vehicle. This may affect the defrost system, decreasing driver visibility, and creating the risk of a crash causing property damage, personal injury or death. Correction: Dealers will replace all HVAC control knobs.
Recall number
2008-268
Recall date
2008-07-30
System affected
Powertrain
Model year(s) affected
2008
Manufacturer Recall Number:
08244
Units Affected:
13
Notification Type:
Safety Mfr
Certain All-Wheel Drive (AWD) vehicles may have been assembled with an incorrectly manufactured transfer case that could cause early failure of drive chain. If the chain breaks, shifting the transmission to "Park" may not keep the vehicle stationary. If the vehicle is parked on an incline or bumped, it may roll and strike a person , an object or vehicle without warning and cause personal injury. Correction: Dealers will inspect the transfer case code and, if necessary, replace the transfer case.
Recall number
2008-249
Recall date
2008-07-14
System affected
Powertrain
Model year(s) affected
2008
Manufacturer Recall Number:
08218
Units Affected:
60
Notification Type:
Safety Mfr
On certain Cutaway vans, the transmission may self-engage into first gear while the vehicle is traveling at highway speeds, thereby causing transmission damage to certain gears. Should this occur at speeds beyond 130 km/h, the engine may shut down (and be able to be restarted with limited operating capability). However, in some cases, the transmission will no longer function in any gear. This could cause the vehicle to lose propulsion which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash. Correction: Dealers will reprogram the Transmission Control Module (TCM) and the Engine Control Module (ECM).
Recall number
2008-244
Recall date
2008-07-09
System affected
Structure
Model year(s) affected
2008
Manufacturer Recall Number:
08205
Units Affected:
13
Notification Type:
Safety Mfr
On certain cutaway vehicle with a 139" wheelbase, the frame rail on the driver's side may be wider than specification. As such, it may contact the fuel tank housing and, over time, cause a fuel leak. Fuel leakage, in the presence of an ignition source, could result in a vehicle fire, causing property damage, personal injury, or death. Correction: Dealers will inspect the clearance between the frame rail and the fuel tank housing. If clearance is not sufficient, dealers will rework the frame rail.
Recall number
2008-120
Recall date
2008-04-10
System affected
Seats And Restraints
Model year(s) affected
2003 2004 2005 2006
Manufacturer Recall Number:
05113C
Units Affected:
106
Notification Type:
Safety Mfr
Certain full-size passenger, cargo and cutaway vans may have front and rear seat belt buckles that will not latch or will not unlatch. There are two conditions that render the buckle inoperative after customer usage. Specifically, (1) with a damaged ejector hood, the latch tongue cannot fully enter the buckle and will not latch, and (2) if the release bar moves permanently out of position the buckle will either be unable to engage the latch or the pushbutton will be unable to unlatch the buckle. Correction: Dealers will inspect buckles and, if found to be inoperative, the entire buckle assembly will be replaced. Note: This is an expansion of recall 2005390.
Recall number
2007-260
Recall date
2007-08-09
System affected
Brakes
Model year(s) affected
2007
Manufacturer Recall Number:
07177
Units Affected:
2,004
Notification Type:
Compliance Mfr
Certain vehicles fail to comply with the requirements of CMVSS 108, requiring the illumination of the stop lamps whenever the brakes are applied. The rear brakes may still be applied although the brake pedal is released and the stop lamps are no longer illuminated. A vehicle driven with the brakes applied can cause overheating of the brakes, resulting in increased stopping distance. Extended stopping distances can lead to a vehicle crash with injury or death. Correction: Dealers will reprogram the Anti-lock Brake System (ABS) module.
Recall number
2005-390
Recall date
2005-12-14
System affected
Seats And Restraints
Model year(s) affected
2003 2004 2005 2006
Manufacturer Recall Number:
05113
Units Affected:
39,243
Notification Type:
Safety Mfr
Certain full-size passenger, cargo and cutaway vans may have front and rear seat belt buckles that will not latch or will not unlatch. There are two conditions that render the buckle inoperative after customer usage. Specifically, (1) with a damaged ejector hood, the latch tongue cannot fully enter the buckle and will not latch, and (2) if the release bar moves permanently out of position the buckle will either be unable to engage the latch or the pushbutton will be unable to unlatch the buckle. Correction: Dealers will inspect buckles and, if found to be inoperative, the entire buckle assembly will be replaced.
Recall number
2005-296
Recall date
2005-10-07
System affected
Steering
Model year(s) affected
2006
Manufacturer Recall Number:
05086
Units Affected:
6,487
Notification Type:
Safety Mfr
Certain vehicles may have been built with a power steering hose that is not to specification. Under extreme steering manoeuvres, such as turning the steering wheel fully to the left or right while braking, the hose may fracture and leak fluid. If this were to occur, power steering assist would be lost and increased steering effort would be required. On vehicles equipped with hydro-boost power brakes, it could also result in loss of power brake assist and increase braking effort would be required. If power steering fluid were to spray onto hot engine parts, an engine compartment fire could occur. Correction: Dealers will inspect the power steering hose(s) for two suspect date codes and replace them if required.
Recall number
2005-033
Recall date
2005-02-15
System affected
Brakes
Model year(s) affected
2004 2005
Manufacturer Recall Number:
05006
Units Affected:
5,014
Notification Type:
Safety Mfr
On certain vehicles, the hydraulic brake booster's pressure accumulator may crack and/or separate from the Hydro-Boost assembly during normal vehicle operating conditions. If a separation occurred and the hood of the vehicle was open, fragments from the accumulator could cause injury to people in the immediate area. In addition, the presence of this crack or fractured surface could allow the hydraulic fluid to leak from the accumulator circuit of the booster assembly. The loss of fluid would cause increased steering and braking effort. Correction: Dealers will test and, if necessary, replace the Hydro-Boost assembly.
Recall number
2005-010
Recall date
2005-01-14
System affected
Brakes
Model year(s) affected
2000
Manufacturer Recall Number:
05001
Units Affected:
7,250
Notification Type:
Safety TC
Certain vehicles are equipped with a hydraulic pump driveshaft that can fracture, resulting in immediate loss of hydraulic power steering assist. On certain vehicles equipped with Hydro-Boost power brakes, the same condition can result in loss of power assist for braking after the reserve pressure is depleted. Correction: Dealers will replace the hydraulic pump. This action is deemed a Customer Satisfaction Campaign and is not being conducted under the Safety Act.
Recall number
2004-216
Recall date
2004-07-07
System affected
Other
Model year(s) affected
2003 2004
Manufacturer Recall Number:
04061
Units Affected:
521
Notification Type:
Safety Mfr
On certain vehicles, the transmission shift cable may allow the transmission indicator (PRNDL) to indicate a different gear selected than the transmission is in. If this condition occurred while a vehicle is resting on an uneven surface, the vehicle could roll away after the driver has exited. Correction: Dealer will inspect and replace the transmission shift cable assembly.
Recall number
2004-138
Recall date
2004-04-20
System affected
Seats And Restraints
Model year(s) affected
2004
Manufacturer Recall Number:
04025
Units Affected:
65
Notification Type:
Compliance Mfr
Certain vehicles do not comply with the requirements of CMVSS 209, "Seat Belt Assemblies". These vehicles may have been produced with seat belt buckle assemblies containing a latch with a brittle condition that may not withstand the force requirements of the standard. In a crash, if the safety belt buckle fails, an occupant's injuries could be greater. Correction: Dealer will install new seat belt assemblies.
Recall number
2004-037
Recall date
2004-01-29
System affected
Brakes
Model year(s) affected
2003 2004
Manufacturer Recall Number:
04004
Units Affected:
4,075
Notification Type:
Safety Mfr
On certain vehicles, the relief valve o-ring seal within the brake hydro-boost module could fail. If this happens during braking applications, the driver may be able to hear an engine compartment noise similar to the sound that occurs when the steering wheel is turned to a full stop position. The driver could also experience a slight increase in steering efforts while braking and parking. Under certain driving conditions, a slight increase in the applied brake pedal effort may be required to achieve the same vehicle deceleration rate as prior to the seal failure. Correction: Dealers will inspect the hydro-boost module, and replace it, if necessary.
Recall number
2003-294
Recall date
2003-11-26
System affected
Visual System
Model year(s) affected
2003
Manufacturer Recall Number:
Units Affected:
27,525
Notification Type:
Compliance Mfr
Certain vehicles do not comply with either CMVSS 105, or CMVSS 135. The red brake warning indicator will not be illuminated while the ABS is modulating the front brakes. Correction: Since this does not pose any safety risk, no corrective action is required.
Recall number
2003-172
Recall date
2003-07-16
System affected
Seats And Restraints
Model year(s) affected
2003
Manufacturer Recall Number:
03039
Units Affected:
54,634
Notification Type:
Compliance TC
Certain vehicles do not comply with CMVSS 225 and 210.2. The Owner's Manual does not include the location symbols for the Lower Universal Anchorage System for Restraint Systems and Booster Cushions and an explanation of the meaning of the symbols. Correction: Owner's will receive an Owner's Manual supplement.
Recall number
2003-154
Recall date
2003-06-16
System affected
Electrical
Model year(s) affected
2003
Manufacturer Recall Number:
03031
Units Affected:
5,259
Notification Type:
Safety Mfr
On certain vehicles, water may enter and corrode the rear licence plate lamp socket causing it to operate intermittently or not at all. The left rear tail lamp may also become inoperative. The temperature of the licence plate lamp socket could increase to the point that it may begin to soften and melt. If the socket assembly were to reach the point of melting, the occupants of the vehicle may notice an odor and smoke at the rear doors of the vehicle. If this odor and smoke were ignored, the plastic could ignite and a fire could occur. Correction: Dealer will install a new sealed rear licence plate lamp socket assembly.
Recall number
2003-040
Recall date
2003-02-19
System affected
Seats And Restraints
Model year(s) affected
2003
Manufacturer Recall Number:
03007
Units Affected:
1,620
Notification Type:
Safety Mfr
On certain vehicles, the seat belt push button may not release the latch plate after the pretensioner is deployed, or alternately the seat belt latch plate may eject during a crash event with a pretensioner deployment. If an occupant was using the seat belt assembly and the latch plate ejected from the buckle assembly during pretensioner actuation, the seat belt assembly may not provide a desired level of occupant restraint. If an occupant was using the seat belt assembly and the push button became stuck in the buckle assembly during pretensioner actuation, pressing on the seat belt push button would not release the latch plate from the buckle to allow the belted occupant to exit the vehicle. Correction: Dealer will replace the front seat belt buckles.
Recall number
2002-237
Recall date
2002-12-12
System affected
Steering
Model year(s) affected
2003
Manufacturer Recall Number:
02063
Units Affected:
479
Notification Type:
Safety Mfr
On certain 2500 and 3500 series vans, the nut attaching the pitman arm to the steering linkage may not be torqued to specification, which could lead to a possible separation. A separation could result in loss of vehicle control, and a crash could occur without prior warning. Correction: Dealer will torque the nut to proper specifications.
Recall number
2002-225
Recall date
2002-11-22
System affected
Steering
Model year(s) affected
2003
Manufacturer Recall Number:
02058
Units Affected:
930
Notification Type:
Safety Mfr
On certain vehicles, the right-hand tie rod end nut may not have been torqued to specification and could loosen, resulting in separation of the tie rod. This could cause unexpected steering input and could cause a crash without prior warning. Correction: Dealers will torque the tie rod end nut to specs.
Recall number
2002-211
Recall date
2002-11-15
System affected
Suspension
Model year(s) affected
2003
Manufacturer Recall Number:
02053
Units Affected:
1,182
Notification Type:
Safety Mfr
On certain 2500 and 3500 series vehicles, a wheel bearing assembly retaining nut was omitted during assembly, which could lead to a possible bearing separation. If this were to occur, the ABS warning lamp would illuminate and the ABS system would be disabled. The driver would also notice a grinding noise, a decrease in vehicle speed and a steering pull in the direction of the affected assembly. Failure to heed these warnings can result in loss of vehicle control and a crash. Correction: Dealers will inspect and replace the wheel bearing assembly if a missing nut is noted during inspection.
Recall number
2000-076
Recall date
2000-03-20
System affected
Other
Model year(s) affected
1999 2000
Manufacturer Recall Number:
00028
Units Affected:
513
Notification Type:
Safety Mfr
On certain vehicles, the power steering cooler hose may separate from the power brake booster fluid flow switch assembly. If this occurs, power steering fluid could flow onto hot engine parts and an engine compartment fire could occur. Correction: Dealers will inspect, and, if necessary, install three new screw clamps to the power steering hose joints.
Select Another Vehicle
Search now